郑大考研网育博书店

2300

主题

0

好友

0

积分

管理员

Rank: 10Rank: 10Rank: 10

UID
251567
性别
保密
考研年份
2016年
帖子
2364
注册时间
2013-4-8
跳转到指定楼层
1#
发表于 2017-3-14 21:32:48 |只看该作者 |正序浏览
权威推荐:郑州大学2023年考研内部权威资料【点击查看】
总部地址:郑州大学主校区育博书店
考研咨询热线:13633846090(同微信,请优先微信联系)
---------------------------------------------------------------------------------------

  1、基本情况

  姓名:翟明

  性别:男

  民族:汉

  籍贯:河南南阳

  职称:教授

  导师类型:硕士生导师

  2、教育背景

  2009-2010,美国犹他大学,材料科学与工程系,访问学者

  2005-今,郑州大学,橡塑模具国家工程研究中心,教师

  2002-2005,新加坡南洋理工大学,机械与制造工程学院,研究员

  1998-2002,大连理工大学,工程力学系,博士

  3、研究领域

  成型工艺力学,计算力学,最优化设计

  4、荣誉奖励

  河南省教育厅学术技术带头人,河南省高等学校青年骨干教师,河南青年五四奖章

  5、学术成果

  在国内外重要学术期刊上发表论文四十余篇,出版著作二部。代表性论文:

  (1)Optimization of Runner Sizes and Process Conditions Considering Both Part Quality and Manufacturing Cost in Injection Molding. Journal of Polymer Engineering, 2011, 31(6-7): 489–494.

  (2)Molecular Dynamics Simulation of Bubble Nucleation in Carbon Dioxide/Hexadecane Solution as an Analog to Foaming of Polyethylene by Super Critical Carbon Dioxide. Journal of Plastic Film and Sheeting, 2011, 27(1-2): 117-126.

  (3)A Study of Gate Location Optimization of Plastic Injection Molding Using Sequential Linear Programming. International Journal of Advanced Manufacturing Technology, 2010, 49(1): 97-103.

  (4)A Numerical Simulation of Full-Shot Microcellular Injection Molding. Journal of Polymer Engineering, 2009, 29(7): 441-453.

  (5)Runner sizing in multiple cavity injection mould by non-dominated sorting genetic algorithm. Engineering with Computers, 2009, 25(3): 237-245.

  (6)Runner Sizing and Weld Line Positioning for Plastic Injection Moulding with Multiple Gates. Engineering with Computers, 2006, 21(3): 218 – 224.

  (7)An Optimization Scheme Based on Flow Resistance to Locate Optimum Gate of Complex Part. Journal of Reinforced Plastics and Composites, 2005, 24(15): 1559-1566

  (8)An Improved Algorithm for the Simulation of Injection Molding Filling Process. Journal of Reinforced Plastics and Composites, 2005, 24(7), 691-698

  (9)Algorithms for Two Gate Optimization in Injection Molding. International Polymer Processing, 2005, 20(1), 14-18

  (10)Algorithm to Optimize Number of Gates and Locations in an Injection Mould. Plastics, Rubber and Composites: Macromolecular Engineering, 2004, 33(8), 330-334
分享到: QQ空间QQ空间 腾讯微博腾讯微博 腾讯朋友腾讯朋友
分享淘帖0 分享分享0 收藏收藏0 支持支持0 反对反对0
您需要登录后才可以回帖 登录 | 注册

Archiver| ( 豫ICP备07041838号 ) |

郑大考研网育博书店 Powered by 育博书店

回顶部